FR 155 Hornet Drone Buildout and Guide

Detailing and giving quick tips for my FlowRotors 155 Hornet hex drone build.

Parts list:

20151221_184137

 

The first step was getting all the parts nice and organized. In addition to what came with the frame i used a few extra screws and spacers to keep the boards from contacting the cf frame/pod.

 

20151225_124138

 

I did a quick dry fit of the frame, screws, pod, and boards before continuing on. I didn’t want a sizing/screw issue after soldering the components later.

20151224_172713

 

 

Step 1 was getting the battery strap through the outer slots in the bottom of the frame (top is shown below). I also screwed in four bolts and used small nuts to use as spacers as well as keeping them secured to the frame body.

20151225_124702

 

Next I added the pdb and placed the kits aluminum spacers. Now is also a good time to tin the pdb for the incoming esc power wires.

20151227_125425

 

Next I connected the esc power wires to the pdb. I also trimmed the wires to make sure the esc’s would land evenly on the frame arms. The green paracord is not necessary but makes the whole build pretty. Each wire is individually sleaved.

20151227_143823

 

 

Removing the pre-soldered motor wires from the esc was a painful but necessary step, you can also see the paracord sleeve better here.

20151228_224225

 

 

All 6 esc’s existing wires de-soldered, it ended up saving close to 12g of weight!

20151229_220042

 

 

Before deciding on the esc <–> motor technique I ended up using I tried just trimming the motor wire extremely short. This worked… kind of. It ended up putting too much stress on the motor wires though and in the end I decided to do the over-under wiring.

20151228_224938

 

Over-under consists of pulling the still long motor wires under the esc and between the power wires then forward.

20151229_221138

 

 

Next trim and solder the now pulled forward motor wires to the esc. This lets you get the esc closer to the motor without putting major stress on the wires. It also makes it easier to flip the motor wires if direction is reversed.

20151229_000702

 

 

After the esc’s were soldered to the motors I soldered their signal leads to the underside of the flight controller. I also soldered up the power for the flight controller and the receiver.

20151230_002045

 

 

I screwed down the flight controller next and plugged in a battery to verify motor direction/correct wiring. I could actually fly horizon mode pretty well like this.

20151231_184548

 

 

Prior to the next step I taped the very bottom of the camera pod sides. They get dangerously close to the flight controller and I didn’t want to risk something shorting.

20160101_232258

 

You can just make out the clearence in the below picture. Its under a mm and so the tape is a great bit of assurance. I connected up 3 sides of the pod and screwed them to the frame here.

20151230_233745

 

Soldering up the microminimosd came next. I used the 5v power from the pdb and and also hooked up the battery monitor leads, pulling the wires around the side of the frame and up through the bottom of the camera pod.

20160101_213756

 

 

Next came wiring up the camera. The paracord didn’t quite reach here but I was able to make sure my video in/out was soldered nicely. I also powered my camera through the vtx.

20160101_230926

 

 

Finally I connected my vtx to the top of the pod. Its power comes from 12v passed through a small lc filter attached to the front of the quad.

20160101_235821

 

 

My proper camera didn’t arrive in time so I temporarily used a small cmos cam, keeping it in the pod with hot glue. The osd was hot glued to the back of the pod where the vtx connects. The hex is now ready to haul fpv style!

20160101_235803

 

Here’s the AUW. About half of that weight comes from the 4s 1000mah battery. (170g’ish)

20151230_232051

 

UPDATE: Proper 1177 camera installed and calibrated

Calibrated using a guide from the S3 wiki

155done1 155done2 155done3

 


Posted

in

by

Tags:

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *